SpeedBox 2.0 for Bosch - Quantity: 20 pcs + 3 free, Bag

(78)

SpeedBox 2.0 for Bosch - Quantity: 20 pcs + 3 free, Bag

Ask a question

+420 702 042 874

info@speedbox-tuning.com

Quick contact

PROPERTIES:
Speed limiter: deactivated
Display shows: actual values
Compatible with displays: KIOX, INTUVIA, NYON, PURION and COBI
Activation: by pressing WALK / + - + -
Compatible with SpeedBox App: NO
This product in not compatible with Bosch 2020 motors!

 More >>
Product code: SB2_B_20+3pcs_BAG

2 880 € incl. VAT

Specify product selection
In Stock
pcs
Add to favourite products

Reliable second generation tuning chip for e-bikes with Bosch motors.

SpeedBox 2.0 tuning chip enables you to suppress the speed limiter on your electric bike. After the chip is installed, your e-bike’s display will show real data, such as maximum and average speeds, daily mileage and cruising range.

How does SpeedBox 2.0 work?

The tuning kit can be activated directly on your bike’s display.  After pressing the WALK button, a value of 9.9 km/h (6.2 mph) is displayed and from now on you will be able to ride at a speed of 40 km/h, 50 km/h and even more than 60 km/h.

To deactivate the tuning kit, press the WALK button again. The value of 2.5 km/h (1.6 mph) will appear on your display and the speed limit will reset to 25 km/h. Your e-bike will then work the same as before installation of the chip.

SpeedBox was also designed for e-bikes that do not have a classic control unit with Walk button. In this case you can just use the combination of + - + -  buttons and SpeedBox will be activated. You can easily deactivate SpeedBox in the same way.

Assembly

When connecting the SpeedBox chip to an e-bike you will find connectors colored to make installation very simple. We have prepared detailed instructions and videos to make installation easy for you. Disassembly of our tuning chip is just as easy. If you have any troubles with installation or disassembly, do not hesitate to contact us.

If you are planning to install SpeedBox on a brand-new bike, make sure you ride it for at least 1 km before the chip is activated.

Download manual
View the correct wire connection

 

Warning

Please note that the operation of this type of modified electric bikes on public roads may be against the law in some countries. The manufacturer takes no responsibility for damages resulting from the use SpeedBox products. Electric bikes equipped with SpeedBox products are not allowed to be used on public roads, cycling paths and public places. Electric bikes equipped with SpeedBox products can be used exclusively on private property and entirely at one’s own risk. The use of SpeedBox may void the warranty of your ebike.

We strongly recommend using other safety features and protective gear to prevent injuries in higher speeds.

Facile à monter
Vitesse réel au tableau de bord
Peut être commandé avec la commande d'origine en roulant

Lenteur de livraison du produit

Was this review helpful? Yes (0) No (0)

Veloce da installare e molto semplice da attivare

Al momento nessuna critica

Was this review helpful? Yes (0) No (0)

Prompt shipping and easy tracking to the US via Czech Post. Easy installation following video (pay attention to speed sensor vs taillight plug!). ... More

none so far.

Was this review helpful? Yes (1) No (0)

WOW!!! Amazing! I absolutely love it! It works as promised!

Was this review helpful? Yes (0) No (0)

Un autre produit Tchèque parfait (l'autre c'est l'imprimante Prusa 3D !). Impossible de se tromper entre les différents connecteurs car ceux fournis s ... More

Aucun.

Was this review helpful? Yes (0) No (0)

It works exactly as described. Can hide it between the motor unit and the plastic shell instead of unscrewing the motor from the frame as described in ... More

Likely because of COBI.bike changing the button function on the thumb controller (while fiddling around with it): caused weird glitch with power mode, ... More

Was this review helpful? Yes (0) No (0)

easy install and best performance

shipping takes more than one week.

Was this review helpful? Yes (0) No (0)

good product, easy to install, very efficient
makes the bike more attractive
to be recommended to everyone

could surely be cheapest
to be discounted when purchase several units

Was this review helpful? Yes (0) No (0)

Next
Comments

Graham Lewis

I purchased speed box 2 for my 2019 trek powerfly with Bosch performance cx line,connecting the cables was no issue ,and when when pressing walk mode I get the 6 mph on the display ,but when I try and pedal I get error code 503 and no drive from the motor.Bike runs fine again when the box is removed .Checked magnet position and that is also correct.

Jiří Voldán (Sales Manager)Administrator |

Please try to uninstall SpeedBox and install it back again. Bad contact between connectors can cause 503 error code.

John Degrand

I tried to install the Bosch Speedbox 2, and it went well to plug in the Big 4 pin header. But when I then tried to plug in the small 2 pin connector from the speedbox into my Bosch Performance Line Gen3 engine, it did not fit.
When I then compared the two headers, I saw that the original header from the Bosch engine was slightly different from the one in the speedbox. The speedbox one had 2 notches, the Bosch original one only 1 notch.

Did I have to buy the speedbox 3? Does that one have a different header for the 2 pin connector?

Jiří Voldán (Sales Manager)Administrator |

Hi John, please send me some photos to info@speedbox-tuning.com, I'll help you through this.

Bob Bush

I installed the Speedbox 2 using the 4-pin display connector and the connector on the far right (of 4) that was grey (details below).

1. Blue block - 2 cables, 1 red, 1 black.
2. Black block - 4 cables, 1 black,1 yellow, 1 green, 1 red. OK
3. Black block with orange cover - 2 cables, 1 red, 1 black.
4. Grey block with orange cover - 2 cables, 1 red, 1 black. OK

Everything seems ok, with it off, bike works normally, limited to 25km/h. When I turn it on, the 9.9 appears on the display, and everything is normal up to 25km/h. Above 25km/h the speed display jumps around erratically and the motor cuts in and out. The display is reading random numbers above 25; 87 then 64 then 42, then back to 80’s, drop below 25km/h and it returns to normal. Press the WALK button again, 2.5 appears and it’s all normal.

So the question is, what wrong with it? Why is the speed display jumping around like crazy when the Speedbox is activated?

Martijn Meester

Your Specs say "This product in not compatible with Performance Line CX 2020 motors!" In this discussion there are answers that it will work.
Will this work on Bosch Performance Line CX, 250 Watt (MY20) (New TREK Powerfully 5 2020)

Jon

Hi, I have a new (2019) TREK Powerfly 5 with Bosch Performance Line CX motor.
I have exposed the cable blocks for the wiring.
There are 4 connector blocks in a row, but I don't know which ones I should be using.
The connector with 4 cables is obviously correct, but there are three other, each with 2 cables, all of them are 1 black, 1 red.
From left to right they are :-
1. Blue block - 2 cables, 1 red, 1 black.
2. Black block - 4 cables, 1 black,1 yellow, 1 green, 1 red. OK
3. Black block with orange cover - 2 cables, 1 red, 1 black.
4. Grey block with orange cover - 2 cables, 1 red, 1 black.

Out of blocks 1, 3 and 4 can you tell me which one I should use please?

Next
Contact us!
Related products