PROPERTIES:
Speed limiter: suppressed
Display shows: actual values
Compatible with the displays: KIOX, INTUVIA, NYON and PURION
Activated by: WALK button

More >>

Product code: SB2B_APC-1

144 € incl. VAT

Specify product selection

In Stock
pcs

Revolutionary process-control module

SpeedBox2 for BOSCH is a revolutionary process-control module which  suppresses the speed limiter of your electric bike. After installation and activation of your SpeedBox for Bosch the display will show actual values. Values such as maximum speed, average speed, distance travelled daily and range are displayed correctly.

The SpeedBox2 is activated by briefly pressing the WALK button located at the front of the control panel. After pressing this button, the current speed of 9.9 km/h is displayed on the control panel for about 3 seconds. This means that the SpeedBox2 is activated. When the WALK button is pressed again, the current speed of 2.5 km/h is displayed. This means that the SpeedBox2 is deactivated, and everything works as if the speedbox had never been installed. The supplementary assistance of your electric bike now works up to its original speed limit of 25 km/h.

SpeedBox2 for BOSCH Performance Line:

SpeedBox2 for BOSCH Performance CX Line:

Facile à monter
Vitesse réel au tableau de bord
Peut être commandé avec la commande d'origine en roulant

Lenteur de livraison du produit

Was this review helpful? Yes (0) No (0)

Veloce da installare e molto semplice da attivare

Al momento nessuna critica

Was this review helpful? Yes (0) No (0)

Prompt shipping and easy tracking to the US via Czech Post. Easy installation following video (pay attention to speed sensor vs taillight plug!). ... More

none so far.

Was this review helpful? Yes (0) No (0)

WOW!!! Amazing! I absolutely love it! It works as promised!

Was this review helpful? Yes (0) No (0)

Un autre produit Tchèque parfait (l'autre c'est l'imprimante Prusa 3D !). Impossible de se tromper entre les différents connecteurs car ceux fournis s ... More

Aucun.

Was this review helpful? Yes (0) No (0)

It works exactly as described. Can hide it between the motor unit and the plastic shell instead of unscrewing the motor from the frame as described in ... More

Likely because of COBI.bike changing the button function on the thumb controller (while fiddling around with it): caused weird glitch with power mode, ... More

Was this review helpful? Yes (0) No (0)

easy install and best performance

shipping takes more than one week.

Was this review helpful? Yes (0) No (0)

good product, easy to install, very efficient
makes the bike more attractive
to be recommended to everyone

could surely be cheapest
to be discounted when purchase several units

Was this review helpful? Yes (0) No (0)

Next
Comments

Jacob

Hi. I have a CANNONDALE Trail Neo Performance line cx 2019
Can i use this tuning?

Jiří Voldán (Sales Manager)Administrator |

Hi Jacob. Yes you can. It will work.

Robert

Hi,

I have done around 1200km with the SpeedBox and I love it. Today for the first time, the display was reading the wrong speed and jumped from 38 to 79 in two seconds. I switched off and on again and had the same issue. No updates have been performed to the Intuvia and Active Line Plus system. Any ideas how I could fix this?

Gio

Hi there, I just got one of these, I can't find instructions on how to install on a 2019 cube acid one with active plus motor. Am I supposed to install without removing the motor completely?

Jiří Voldán (Sales Manager)Administrator |

Hello, you basically need to get behind a cover of the motor. It does not always mean that you gotta remove the motor completely.

Bart

Hi, I have a speedbox2 installed on a regular active line w intuvia display. It works well but the problem I have is that sometimes when I've activated the speedbox (w walk) and I'm cycling suddenly all motor support stops (display still works) and I have to power down, remove the display and put it back again to get the bike working again. Sometimes it does not happen for weeks, other times it happens like 2 or 3 times during a ride. I've already had the speedbox2 replaced but it gave the same result. Is this a known issue ?

Jiří Voldán (Sales Manager)Administrator |

Hi Bart. It's not actually. Contact me on info@speedbox-tuning.com. Tell me exact name of your eBike. Try if uninstallation of SpeedBox helps. Is there any error code on the display?

Ronald Fendt

Hi, to all Speedbox2 work great. But i find something for which i need some answer, to long to descripe

Next
Contact us!